---===SME_1503_00005_0001.djvu===---
Pub.No.00ELT0043, OCTOBER 2013 
---===SME_1503_00005_0001.djvu===---
Pub.No.00ELT0043, OCTOBER 2013 
---===SME_1503_00005_0002.djvu===---
GROUP INDEX 
MODIFICATION SUMMARY ............ 
GENERAL ........................................ 
MANUAL TRANSMISSION.............. 
REAR SUSPENSION ....................... 
ANTI-LOCK BRAKE SYSTEM 
(ABS)................................................ 
STEERING <POWER STEERING 
(Except FB70)>................................ 
BUNPER, FRAME AND 
REAR BODY .................................... 
CAB MOUNTING AND TILT ............ 
HEATER, AIR-CONDITIONER 
AND VENTILATION ......................... 
FOREWORD 
This Shop Manual is published for the information and 
guidance of personnel responsible for maintenance of 
Mitsubishi Fuso CANTER series truck, and includes pro- 
cedures for adjustment and maintenance services. 
We earnestly look forward to seeing that this manual is 
made full use of in order to perform correct services with 
no wastage. 
As this Shop Manual is published as a supplement to the 
following Shop Manual, please refer to the following for in- 
formation not included in this manual. 
CANTER chassis .. .......... .......... ... .Pub. No. TWSE0611 
For more details, please consult your nearest authorized 
Mitsubishi Fuso dealer or distributors. 
Kindly note that the specifications and maintenance ser- 
vice figures are subject to change without prior notice in 
line with improvement which will be effected from time to 
time in the future. 
OCTOBER 2013 
Applicable models 
FE, FG 
©2013 Mitsubishi Fuso Truck & Bus Corporation Printed in Japan 
---===SME_1503_00005_0003.djvu===---
This Shop Manual contains the information classified into the following groups. 
If any system or equipment has two or more variations with significantly different construction, the variations are 
handled as different groups. These groups are identified by different alphabets preceded by the same number. 
1. ENGINE volume (Pub.No.00ELT0042) 
2. CHASSIS Supplement volume (Pub.No.00ELT0043) 
3. ELECTRICAL volume (Pub.No.00ELT0044) 
Group No. 
Group subject 
00 
GENERAL 
11 
ENGINE 
12 
LUBRICATION 
13 
FUEL AND ENGINE CONTROL 
14 
COOLING 
15 
INTAKE AND EXHAUST 
Group No. 
Group subject 
00 
GENERAL 
22 
MANUAL TRANSMISSION 
34 
REAR SUSPENSION 
35E 
ANTI-LOCK BRAKE SYSTEM (ABS) 
37B 
STEERING <POWER STEERING (Except FB70)> 
41 
BUMPER, FRAME AND REAR BODY 
42 
CAB MOUNTING AND TILT 
55 
HEATER, AIR-CONDITIONER AND VENTILATION 
Group No. 
Group subject 
54 
ELECTRICAL 
---===SME_1503_00005_0004.djvu===---
1 
MODIFICATION SUMMARY 
---===SME_1503_00005_0005.djvu===---
2 
1. Chassis 
This section describes only the differences from "CANTER Shop Manual chassis" (Pub. No. TWSE0611). 
Be sure to check the differences described in the following before servicing. 
Group 
Contents of different points 
Application 
Service 
procedure 
00 (1) New powertrain combination added. 
(2) Inspection procedure using diagnosis codes is changed. 
(3) A topic for the definitions of vehicle identification number is added. 
All models 
See Gr00. 
22 (1) The transmission mounting support is changed. 
Removal sequence 
FE85C-Z 
Same as 
before except 
these explained 
here. 
(2) The gear shifter upper is changed. 
All models 
See Gr22. 
(3) An L-joint is added to the vehicle speed sensor. 
FE85CH, FG, 
FE85PH 
See Gr22. 
(4) The counter lever of the transmission control is changed. 
All models 
See Gr22. 
25 (1) The propeller shaft model applications to the vehicle models shown in "Spec- 
ifications" table are changed. 
All models 
Same as 
before except 
these explained 
here. 
34 (1) The rear stabilizer is added. 
FE8 
See Gr34. 
1 Propeller shaft (See Gr25.) 
2 Parking brake cable (See Gr36.) 
3 Transmission 
* 
a: Transmission mounting support 
Item 
Specifications 
FE7, FG <Front axle> FE8, FG <Rear axle> 
Propellar shaft Model 
P2 
P3 
MODIFICATION SUMMARY 
---===SME_1503_00005_0006.djvu===---
3 
37B (1) The specifications for the power steering gear assembly and power steering 
oil pump differ. 
Power steering gear assembly 
Power steering oil pump 
All models 
Same as 
before except 
these explained 
here. 
Group 
Contents of different points 
Application 
Service 
procedure 
Item 
Specifications 
FE (except 
FE85CH, FE85PH), 
FG 
FE85CH, 
FE85PH 
Manufacturer 
Hitachi Automotive Systems Steering 
Type 
Ball nut type 
Form 
Integral form 
Manufacturer's item number 
454-00004 
455-00002 
Gear ratio 
22.2 
22.7 
Cylinder diameter 
mm 
80 
85 
Item 
Specifications 
4D33 
4D34 
Manufacturer 
Kayaba industry 
Type 
Vane type 
Manufacturer's item number 
B4230-09058 
B4230-09037 
Delivery rate 
cm 
3 
{mL}/rev. 
9.6 {9.6} 
Adjusted flow volume 
dm 
3 
{L}/min. 
6to8{6to8} 
Adjusted pressure (relief valve) 
MPa {kgf/cm 
2 
} 
11.8 {120 } 
10.8 {110 } 
Permissible revolutions 
rpm 
600 to 6500 
+0.2 
--0.5 
+2 
--5 
+0.2 
--0.3 
+2 
--3 
---===SME_1503_00005_0007.djvu===---
4 
37B (2) The following parts are different in "STEERING COLUMN". 
The shock absorbing rubber is abolished. 
The shape of the lever shaft bolt is changed. 
The shape of the steering column support is changed. 
Disassembly sequence 
All models 
Same as 
before except 
these explained 
here. 
(3) The service procedure for power steering gear assembly and drag link is 
changed. 
All models 
See Gr37B. 
41 (1) The front bumper is changed. 
FE7 
See Gr41. 
42 (1) The tightening torque for the cab mounting bolts is different. 
All models 
See Gr42. 
(2) The tightening torque for the front mounting bracket attaching bolts is differ- 
ent. 
FE7 
See Gr42. 
Group 
Contents of different points 
Application 
Service 
procedure 
1 Lever cover 
2 Lever protector 
3 Pin 
4 Lock lever 
5 Lever shaft nut 
6 Lever shaft bolt 
7 Spacer 
8 Pin 
9 Collar 
10 Tilting and telescoping lever 
11 Spring 
12 Steering column support 
13 Steering column 
* 
a: Link plate 
: Non-reusable parts 
MODIFICATION SUMMARY 
---===SME_1503_00005_0008.djvu===---
5 
43 (1) The upper door trims are changed. 
Door Panel 
Disassembly sequence 
All models 
Same as 
before except 
these explained 
here. 
51 (1) The service standards for the wiper arm are changed. 
Service standards 
All models 
Same as 
before except 
these explained 
here. 
Group 
Contents of different points 
Application 
Service 
procedure 
1 Glass holder 
2 Door glass 
3 Manual regulator 
<Manual control type> 
Regulator and motor 
<Electrical control type> 
4 Sash garnish 
5 Beltline molding 
6 Delta garnish 
7 Door lock 
8 Door lock cylinder 
9 Outside handle 
10 Ash tray 
11 Weatherstrip 
12 Inside handle inner 
cover 
13 Inside lock cable 
14 Inside open cable 
15 Inside handle 
16 Spring 
17 Upper door trim 
18 Runchannel 
19 Protector 
20 Door check 
21 Door panel 
Location 
Maintenance item 
Standard value 
Limit 
Remedy 
7 
Wiper arm force 
to press blade 
against wind- 
shield 
Standard- 
width cab 
5.6±0.5N{570±5gf} -- 
Replace 
Widecab 5.9±0.5N{600±5gf} -- 
---===SME_1503_00005_0009.djvu===---